Heat-Resistant for BMW Brake Pad with SGS ISO 9001 Approved

Model NO.: Brake Pad

Main Market: South America, North America, Eastern Europe, Mild East, Africa, Western Europe

Friction Coefficient: 0.32-0.40

Wear Rate: 0.2-0.45

Hardness: 40-60hb

Friction Material: Heat-Resistant: Friction Coefficient & Wear Rate S

Backing Plate: Baosteel Q2358

Silencer: Though Klaus Tester

Thermal-Protective Coating: Though SMT-4 Temperature Tracker

Warranty: 30, 000-50, 000 Km; 120% *Fob Value Compension

Delivery Time: 35 Days; 0.1% *Fob Contract Value Penalty of Delay

Efficiency: 24-Hour Reply; 5 Days to Close Claim

Trademark: CEDARS

Transport Package: Neutral Package; Cedars Package; Special Package

Specification: OE Brake Pads Standard Size

Origin: China(Mainland)

HS Code: 8708301000

Full Range of Brake Pads

Â

Quality Brake Pads

Advanced Inspection Equippment

20-8-3Â Supplier Development Model

Practical Warranty, Delivery on Time Heat-Resistant for BMW Brake Pad with SGS ISO 9001 Approved

Heat-Resistant for BMW Brake Pad with SGS ISO 9001 Approved

Â Â Â Â Â Â Â Â Â a. 12 months after B/L date Â Â Â Â Â Â Â Â a. Â 35 days (Depends on order quantity) Â Â Â Â Â Â a. 24-hour Response Â Â Â Â Â Â Â Â Â Â Â Â Â Â Â Â Â Â Â
b. Â 120%*FOB compensation; Â Â Â Â Â b.Â 0.1%*FOB penalty per day of delay Â Â Â Â Â Â Â Â b.Â 5 working days to close claim Â

Reliable Auto Parts Supplier

Adjustment of the Main Drive Gap of Wheeled Construction Machinery Drive Axle

1. Check and adjust the bearing clearance of the driving bevel gear. The bearing clearance of the driving bevel gear is generally 0.05-010mm. When the clearance exceeds 0.10mm, it should be adjusted: fix the dial indicator on the axle housing, and the contact of the meter is against the driving gear The outer end of the gear shaft, and then axially pry the upper flange of the gear shaft, the absolute value of the maximum and minimum readings of the dial gauge is the bearing clearance; when adjusting, you can increase or decrease the adjustment gasket between the inner ring of the driving gear bearing and the shaft shoulder. If you add a gasket, the bearing becomes loose, and vice versa.

2. Inspection and adjustment of the bearing clearance of the driven bevel gear. The normal clearance of the left and right bearings of the driven bevel gear is 0.05-0.10mm, which can be adjusted by the adjustment rings on both sides of the differential housing. First, remove the lock plate on the adjustment ring, and then twist the two adjustment rings to adjust (the two adjustment rings must be screwed in or out at the same time to ensure the meshing gap and impression of the gear pair); after adjustment, the driven gear should be It is suitable to rotate flexible and have a little resistance, but there is no loose feeling.

3. The adjustment of the thrust screw of the driven Wheel Loader Bevel Gear. For construction machinery with thrust screws on the back of the driven gear (such as ZL50 loader), the gap between the end of the thrust screw and the back of the driven gear should be 0.20-0.40mm . When adjusting, first loosen the fixing nut, then tighten the screw and back 1/3 turn, and then lock the fixing nut.

4. Inspection and adjustment of the meshing clearance and impression of the driving and driven bevel gears. Inspection methods and standards: When checking the meshing of the driving and driven bevel gears, the tooth surface of the driving bevel gear is usually coated with red lead oil first. In the case of gear meshing, turn the gear with a little resistance, and then check the traces on the Teeth of the driven gear; when meshing correctly, the contact length of the imprint should be about 2/3 of the full tooth length, and the contact traces are 2-4cm from the small end .(Main Drive,Axle Of Sdlg Loader,Pinion Ring Gear,Wheel Loader Bevel Gear)

Main Drive

Main Drive,Axle Of Sdlg Loader,Pinion Ring Gear,Wheel Loader Bevel Gear

Shandong Tianfu International Trade Co.,Ltd. , https://www.tfloaderparts.com