601783standard and Nonstandard NBR Viton Oil Seal for Industrial Parts Taiwan

Model NO.: 601783
Standard: Standard, Nonstandard
Temperature: -25 Centigrade - 250centigrade
Hardness: 75-90 Shore
Color: Black,Brown, or Color Required
Application: Automobile, Engineering Machinery,Agricuture
Certificates: SGS
Shipping: by Sea,by Air,by Railway
Trademark: MKS
Transport Package: Plastic Bag or Brown Bag with Carton
Specification: all size
Origin: China
HS Code: 40169310
601783standard and Nonstandard NBR Viton Oil Seal for Industrial Parts Taiwan

PROPERTIES

601783standard and Nonstandard NBR Viton Oil Seal for Industrial Parts Taiwan

SHAFT SPEEDS AND LIP MATERIALS

An important consideration when selecting the lip material is the shaft speed (measured in rotations per minute),circumferential speed (measured in feet per second),and shaft diameter(measured in inches).These conditions determine whether or not a given elastomer will operate properly.
The graph below offers general guidelines for determining the compatibility of silicone.fluorocarb
-on,polyacrylate and nitrile with specific shaft and circumferential speed.For more information,ple
-ase contact with us.

601783standard and Nonstandard NBR Viton Oil Seal for Industrial Parts Taiwan




METAL CASE AND SPRING
The Other major components of an oil seal are the metal case and garter spring.
Below lists the material specification MKS uses of its components.
There are basic types of seals:

1)      Static Seals:
The function of a static seal is to creat a barrier between non-moving surfaces. Typical examples would be a valve cover gasket or O-ring.
601783standard and Nonstandard NBR Viton Oil Seal for Industrial Parts Taiwan



2)      Axial Mechanical Seals:
These are face type seals in which the sealing contact is between radially mounted components. One is usually stationary and seal contact pressure is applied by a spring mechanism.
601783standard and Nonstandard NBR Viton Oil Seal for Industrial Parts Taiwan



3)      Dynamic "Radial"Seals:
A dynamic radial seal creates a barrier between surfaces in relative motion. One is usually stationary while the other rolates.The cross-section shown below identifies the most common parts of a shaft seal.

601783standard and Nonstandard NBR Viton Oil Seal for Industrial Parts Taiwan




FITS&TOLERANCES:
Bore Diameter Bore Tolerance Nominal Press Fit Seal O.D.Tolerance
Inch Inch Inch Inch
Up to 3.000 ±.001 .004 ±.002
3.001 to 4.000 ±.0015 .005 ±.002
4.001 to 6.000 ±.0015 .006 +.003
6.001 to 8.000 ±.002 .006 -.002
8.001 to 9.000 ±.002 .007 +.006
9.001 to 10.000 ±.002 .007 -.002
10.001 to 12.000 ±.002 .007 +.006

 
SHAFT RECOMMENDATIONS

Shaft Diameter                                     Tolerance
Up to 4.000 shaft                                     ±.003
4.001 to 6.000 shaft                                ±.004
6.001 to 10.000 shaft                              ±.005

 
 
PRESSURE LIMITS
Shaft Speed-FPM Maximum               Pressure-PSI
0-1000                                                           7
1001-2000                                                     5
2001 and Higher                                            3

 
ECCENTRICITY LIMITS
Speed Range         Max.Misalignment          Max Shaft Run-Out
0-800 RPM                              0.015  in ECC                            0.025 IN TIR        
800-2200 RPM                        0.010  in ECC                            0.020 IN TIR          
2200-4200 RPM                      0.010  in ECC                            0.015 IN TIR                

For Further require, please kindly connect with us,Thanks

MSB Horizontal Sand Pump

Hebei Yongquan Pump Industry Co., Ltd. , http://www.cnsolarpump.com